Siemens G120 & G120C AC VFD Driver Training

Name: Siemens G120 & G120C AC VFD Driver Training
Rating: 4.1 (192 reviews)

Siemens G120&G120C AC VFD Driver Training from basic to advanced level, control all your motors easily, 8 subtitles .

Created bySerkan Büyüktopçu

Last updated 11/2025

English

English [Auto],

What you'll learn

Basic Structure and Operation: Students will learn about the main components of the drive and how it controls motor speed.
Commissioning and Parameterization: They will gain the skills to connect the drive to a motor, configure basic and advanced parameters,
Troubleshooting: Students will learn how to identify common faults, understand error codes, and apply methods to solve problems.
Communication and Control: You will learn, how to control manymotors, using Profinet& Telegram, with out any dijital or analog input- out using.

Course content

1 section • 20 lectures • 1h 10m total length

G120 Driver Tecnical Data4:56
Explore Siemens G120 and G120C drives, their connection differences, and how to choose power, communication, and control modules, then enter parameters with Starter, Sizer, Start Drive, Profinet, and BOP/IOP.
G120 Driver introduction Details5:58
Explore Sinamics G120’s modular inverter design, featuring a power module, a control unit, and an operator panel. Configure cost-effective solutions with the dt configurator for your application.
G120C Driver introduction Details3:09
Provide an introduction to the G120C driver within the Siemens G120 and G120C AC VFD driver training, outlining key details for understanding and practical use.
G120-G120C Driver Psrameter Setting Methods6:44
Set up the G120/G120C via the basic panel, IOP, or starter software, then use the status screen wizard with bar graphs and trend view for Hz and PID tuning.
G120 Driver İntroduction4:03
Explore the G120 driver as a power module plus a control unit with PROFINET communication, focusing on PM240 for general use and USB programming via TIA Portal.
Motor Control with BOP0:51
Learn how to engage the motor through the panel, operate in manual mode, set rpm values, start and adjust speed, and stop the motor.
Motor Terminal Conneciton0:52
Explore motor terminal connections for the G120 drive, examining delta and star windings, voltage options of 230 volts in delta and 400 volts in star, and 50/60 Hz operation.
Motor Control with PLC program2:19
Operate a motor via a plc program, energize Q0.0 to start, I0.1 for clockwise rotation, and drive speed through potentiometer set point via the relay-linked driver up to 3000 rpm.
CU240E Terminal Conneciton Diagram1:05
Connect CU240E-2 terminals with a 10-volt source to terminals 2 and 4, bridge inputs 0 and 1 for start and reverse direction, and control motor speed (0-3000 rpm) via voltage.
Entering Motor Parameters to G120 Drive and selecting macro10:01
connect the g120 drive to the motor, energize the unit, and use a macro with a potentiometer to set speed. enter key parameters for 50 Hz and 230 V.
Motor Dirver Potentiometer Connection2:34
Learn to connect an external potentiometer to a Siemens G120 and G120C vfd, wire digital inputs 1 and 0, and monitor setpoint-driven motor speed up to 3000 rpm.
Entering parameters using Tia Portal6:26
Learn to enter motor parameters for a Siemens G120 drive using TIA Portal and StartDrive, wiring an external potentiometer, configuring motor data, and uploading via Profinet.
Commissioning Screen Using4:34
Load and apply the configured G120 driver settings to the driver and PLC, go online via the control panel, and verify rpm up to 3000 in the TIA Portal.
Telegram Settings& Motor Control with PLC4:52
Learn to add a PLC, connect it via Profinet, and control the Sinamics drive using telegrams to read and send data, with free and standard telegrams.
Read Motor data from Driver via Telegram2:12
Read motor data from the driver via telegram using free telegram to read voltage (r25) and current at addresses 256-260. Enable adjustments and upload them to the driver and PLC.
Download program to PLC & Driver1:24
Connect the driver, computer, and PLC via the driver's ports in a ring topology without a switch. Upload the software to the PLC, then to the driver, and wait.
Go Online, Set Value Send to Driver & Monitoring Data2:23
Go online, send the PLC set value to the Siemens G120/G120C driver, and monitor current, voltage, and motor speed in the parameters page.
Read real value of Motor from PLC2:46
Learn to read motor data from a PLC via the Siemens G120 and G120C driver, retrieving voltage, speed, frequency, and current using an algorithm to derive real values from driver.
Modify SINA SPEED block2:49
Demonstrates modifying the sina speed block to add a direction input that reverses motor rotation, upload the program to the plc, and test with a 1250 set value.
Control your Motor From SCADA1:00
Control your motor from SCADA by sending a 500 set value, enabling the axis, and starting the motor to monitor current, voltage, frequency, speed, and reverse direction.

Requirements

Having something like a basic level PLC is enough.

Description

“This course contains the use of artificial intelligence.”

Our videos are available with subtitles in English, Hindi, Arabic, Spanish, Russian, Portuguese, German, and Japanese.

Siemens G120&G120C Drive Course: Take Your Career to the Next Level,1080p Videos, High-Resolution Audio,

Do you want to specialize in industrial automation and stand out in your career? The Siemens SINAMICS G120&G120C drives, which combine energy efficiency with performance, are a cornerstone of modern industry. This comprehensive course will help you get ahead by teaching you all the features of these powerful drives.

What You Will Learn

Fundamentals to Advanced Knowledge: Starting with the basic operating principles, you'll learn to manage different motor control modes using advanced functions and application macros.
Practical Commissioning: You will gain hands-on experience with all processes, from the physical installation and wiring to parameter setting via the operator panel (BOP) and initial startup. You will be able to perform commissioning procedures safely and accurately.
Communication Skills: You'll understand how to communicate with and control the drive using external devices (like a PLC) via the Profinet &Telegrams, which has become an industry standard for communication.
Troubleshooting and Maintenance: You will gain the ability to understand fault codes, diagnose potential problems, and find quick solutions. This will allow you to play an effective role in maintenance and repair processes.

This training will make you more competent in automation projects and help you become one of the qualified experts the industry needs. Equip yourself with the latest technologies in the sector and give your career a new direction.

Who this course is for:

Anyone working in engine and drive operations who wants to increase efficiency in the system can participate in this training.