Pipe Wall thickness Calculation II Allowables II PT Rating
What you'll learn
- Pipe Wall thickness Calculation II Allowable stress II PT rating II ASME B31.3
- Piping, Oil & Gas awareness
•What is pipe
•Understanding the Pipe schedule
•Relationship between outer, inner diameters w.r.t. Pipe wall thickness.
•Why always minimum thickness is desirable?
1.Dimensional standards for Carbon & stainless steels (ASME 36.10 & 36.19)
•Understanding the Standards
•Total scope covered in standards
2.Pipe wall thickness Calculation as per ASME B31.3 (Class conditions & Line Conditions)
•What are various inputs required to start calculating pipe thickness?
•Where do we get the inputs from?
•Understanding Co-relation between Various ASTM Standards
•Understanding the PT rating concept w.r.t ASME 16.5
•Understanding the Allowable stresses, Tensile stress & Yield Stress w.r.t Stress-strain diagram
•Unit system used while referring code & standards while calculating wall thickness?
•Actual Pipe wall thickness calculations (4” Carbon steel)
•Pipe wall thickness calculation based on line conditions given in Line list.
Frequently Asked Questions:
What is ID and OD of pipe?
The outside of the pipe is always larger than the inside. The difference between the inside diameter (ID) and the outside diameter (OD) is due to the thickness of the wall.
What is the thickness tolerance in pipe?
The most common tolerance on the wall thickness of straight pipe is 12.5%. This means that the wall thickness at any given location around the circumference of the pipe must not be less than 87.5% of the nominal wall thickness.
What is required thickness?
The minimum thickness without corrosion allowance for each element of a pressure vessel based on the appropriate design code calculations and code allowable stress that consider pressure, mechanical, and structural loadings.
What unit is thickness?
A "mil" is a unit of thickness equal to one thousandth of an inch (. 001 inch). To convert mil to inches, take mil and divide by 1000.
What is minimum required thickness?
The thickness without corrosion allowance for each component of a piping system based on the appropriate design code calculations and code allowable stress that consider pressure, mechanical and structural loadings.
Is pipe sized by ID or OD?
Tube is measured by outside diameter, pipe is measured by inside diameter.
How do you calculate percent thickness?
t = P * D / (2 * F *S * E)
1. t : Calculated Wall thickness (mm)
2. P : Design pressure for the pipeline (kPa)=78 bar-g=7800 KPa.
3. D : Outside diameter of pipe (mm)= 273.05 mm.
4. F : Design factor = 0.72.
5. S : Specified Minimum Yield Strength (MPa)=359870 KPa for the specified material.
6. E : Longitudinal joint factor = 1.0
What is STD in piping?
In pipes engineering, STD refers to standard thickness. Each pipes was produced to have one thickness that was later termed as STD. Schedule STD Steel Pipes is available in extra strong (XS), extra heavy (XH), double extra strong (XXS), and Double extra heavy (XXH).
What is ASME B36 10M?
B36.10M Welded and Seamless wrought steel pipe
This standard covers the standardization of dimensions of welded and seamless wrought steel pipe for high or low temperatures and pressures.
What is ASME B36 19m?
This Standard covers the standardization of dimensions of welded and seamless wrought stainless steel pipe for high or low temperatures and pressures. The word pipe is used, as distinguished from tube, to apply to tubular products of dimensions commonly used for pipeline and piping systems.
Why is it called Schedule 40?
Why is it called schedule 40 pipe? The pipe numbers are non-dimensional. In other words, SCH 40 doesn't mean the pipe is 40 millimeters or 40 inches in diameter. The parameters for each schedule are determined by the ASME B36
Which is thicker Schedule 80 or Schedule 40?
The major difference between schedule 40 and schedule 80 pipe is the wall thickness, inside diameter, and their weight. Schedule 80 will have a greater wall thickness, a smaller inside diameter and a higher weight than Schedule 40 pipe at a given nominal pipe size.
Who this course is for:
- Piping Design engineers & designers, Mechanical Engineers
Hi ! I 'm Atul. I am PMP certified Piping Engineer with more than 18+ Years of experience. Worked in the field of piping design and plant layout for various industries such as refinery, petrochemical & chemical.
Developed passion about Piping while working with national & international engineering consultants on diverse projects involving international clients.
Developed courses on Piping Engineering to share the knowledge gained after working with many industry experts, through out these years.
I genuinely believe it's the best on the market and you will have best learning experience.
Sign up to my courses and join me in this amazing adventure today.