Mastering the design of professional PCB using EasyEDA

Name: Mastering the design of professional PCB using EasyEDA
Rating: 4.1 (26 reviews)

Design and order your PCB boards with an easy way and order them from the cheapest factory

Created byHamdy egy

Last updated 9/2019

English

English [Auto],

What you'll learn

By the end of this course you will know how to order your design with cheapest way
You will be easily able to create double layer PCBs
You will know how to create Surface mount PCB
You will design some projects and sell them
All problems for designing the PCB's will be solved with an easy way
I will show how you can choose the correct pcb components for your project
you will learn how to create your component package if it is not exist
Also you will learn how to design many projects on the same board to make save
I will teach you how to get your Gerber files and order your pcb by them

Course content

4 sections • 30 lectures • 3h 34m total length

Open the tool for the first time5:29
Discover how to use EasyEDA, the online PCB design tool, to create schematics, convert them to PCB layouts, manage libraries, and collaborate on projects after registering an account.
The steps required for designing a PCB board0:20
First Step: The basics of the one relay channel module8:36
Explain how a relay module uses a transistor as a switch to drive a 5-volt coil for high-voltage devices, including normally open and normally closed contacts and basic protections.
Sec Step: The Proteus simulation of the 1R channel module4:17
Advance your PCB design skills with a second step through the Proteus simulation of the 1R channel module.
Step3: The Hardware of the 1R channel Module6:25
Connect the relay module by wiring the transistor to ground and 5 volts for the coil. Connect the base through a resistor to the external circuit via a TB block.

Step 4: The schematic and the PCB of the first project23:51
Design a one-channel relay module schematic in easyeda and convert it to pcb. Place resistors, transistors, relays, tb blocks, and pin headers, then wire and validate connections.
The schematic in 4 minuets without explaining4:27
Master professional PCB design using EasyEDA by rapidly creating a schematic in four minutes. Learn a concise workflow without explanations to produce clean schematics for professional PCB design.
Step 5: The PCB Design10:40
Convert the relay module schematic to a pcb design, place and align components, route tracks, and adjust widths and units before reviewing a 3d view of a single-layer board.
The same PCB Without explaining3:00
Design a professional PCB with EasyEDA and learn to reproduce the same PCB without explaining.
A mistake in the previous project8:29
Correct a mistake in the previous project by moving wires from the top to the bottom layer on a double layer pcb, using vias for through-hole components.
Important video for multi-layer PCB
Auto route property to connect components automatically4:19
Explore using the auto route property to connect all components automatically, convert to abc to design or update pcb designs, adjust clearance, and switch routes between top and bottom layers.
Adding the ground panel to the project5:52
Add a ground plane in EasyEDA using the copper area tool. Increase clearance, connect the ground in the schematic, and update the PCB to reduce noise and copper usage.

Discussing the different layers of the pcb10:13
Learn how EasyEDA models pcb layers—top and bottom copper, solder mask, and silk layer—and how to export and print top copper, bottom copper, and silk layers.
The components dimensions ( very important )6:14
Understand the importance of component dimensions and power ratings, comparing three-watt and one-watt resistors in power electronics, and choosing suitable through-hole or surface-mount packages such as 0603.
The schematic of the second project (very important for large projects)17:24
Controlling the border shapes and dimensions10:41
Learn to customize PCB borders in EasyEDA by drawing shapes, setting border dimensions to 50 mm by 75 mm, adjusting line thickness, and placing components inside for 3D view.
How to align the components4:23
Learn to align resistors, LEDs, and transistors inside the project border using left, right, and top alignment in EasyEDA, then distribute spacing for a clean PCB layout.
The holes required for installing the board2:54
Design mounting holes for PCB installation in boxes or cases using the hole option, position bolts and screws, adjust hole size, and review the 3D view for enclosure fit.
Putting all the components inside the board10:22
The unconnected pin3:08
Identify unconnected pins in your schematic before converting to PCB, connect them with a net, and apply the connected flag before saving and converting again.
Finishing the connection with some important new features18:40
Connects components across top and bottom layers using vias, layer conversion, and two-layer routing, with track angle control and ground panel considerations.
Another important features3:20
Learn key EasyEDA pcb design features: hide/show layer components, manage top and bottom layers, holes as vias indicated by gray color, and adjust hole shapes and sizes.
How to put your company name and logo on the board8:20
Learn to edit component labels, rename parts such as R1 and Q1, and adjust text rotation and position; insert your company logo and manage silk versus copper layers.
The ground panel for the double layer board1:49
Learn to use the ground panel on a double-layer PCB in EasyEDA by connecting top and bottom ground pins with the cover area option, eliminating stray blue connections.
Combine many boards in the same design8:26

Exporting the Gerber File to send it to the factory8:28
How to order your board from the most cheapest factory with high quality14:08
Two Videos for the two orders from JLCPCB for two different persons
I will show you my boards once i received them form the factory, but until then these two orders for many boards designed by JLCPCB factory
https://youtu.be/h4Aw9vxuycQ?t=594

https://youtu.be/OpPBqCqzF80?t=339
Create the PCB layout for any electronic component

Requirements

Electronic basics only

Description

Breadboards are great for prototyping circuits, but they aren’t so good for actually using the thing you’re building. At some point, you’ll probably want to make a project more permanent. The best way to do that is to put it on a PCB.

In this course you will learn the designing of a professional PCB boards with the most easiest online tool

Also I will teach you how to order your board from the most cheapest factory with high quality and with a good offer for the shipment

you will learn all features that makes you able to design any project small or large

Who this course is for:

Engineers
Hardware hoppiest

Mastering the design of professional PCB using EasyEDA

What you'll learn

Explore related topics

Course content

Introduction5 lectures • 25min

Design the PCB of the 1R module with single layer8 lectures • 1hr 1min

The double layer PCB boards13 lectures • 1hr 46min

The Manufacturing process of the board4 lectures • 23min

Requirements

Description

Who this course is for: