ESP32 Bootcamp: A Step By Step Practical Approach

Learn to build internet-connected IoT projects with the ESP32, using a Wi-Fi breakout board, step-by-step hardware and software workflows, and cloud services to link sensors, buttons, and online information.

Discover hardware and software requirements for the ESP32 bootcamp, including the ESP32 toolbelt board with wifi, the Arduino IDE, sensors, resistors, and jumper wires, plus free account setup for automation.

Explore the ESP32 pinout on the DOIT board, covering SPI, I2C, ADC, PWM, and UART interfaces, and how to choose safe input or output pins.

Set up Arduino IDE and ESP32 board package, install the USB driver for the board, and upload a sketch that connects to your home wifi.

Learn the ESP32 development board, a low-cost system on chip with Wi-Fi and Bluetooth, dual-core 32-bit processing, built-in peripherals and sensors, and programming with the Arduino IDE for IoT projects.

Add the ESP32 package URL in preferences, install ESP32 via board manager, select the ESP32 v1 board, and install the USB-to-UART bridge driver.

Connect and configure the ESP32 board, select the right board and com port, upload a wifi scan example using the wifi library, and view results in the serial monitor.

Learn to blink the ESP32 built-in led by adjusting pin 2 in the Arduino IDE, using setup and loop with digital write and delay, and uploading the sketch.

Learn to read ESP32 internal capacitive touch sensors as buttons with the touch function, print readings to the serial monitor, and drive a red LED based on a 50 threshold.

Learn to read analog signals on the ESP32 using ADC channels and the analogRead function, including pin 36 (adc1 channel 0) and 12-bit 0–4095 range, 3.3V max.

Program pwm signals on the ESP32 with channel zero, 5 kHz, eight-bit resolution, attach to pin two, and adjust duty cycle from 0 to 255 to fade the LED.

Learn to drive a servo with pwm on ESP32, setting frequency, channel zero, eight-bit duty, pin five, and a 90-degree position with a 21 duty cycle.

Identify the hardware and software requirements for the ESP32 bootcamp, including programming software for Arduino without coding, the Arduino IDE, USB drivers, and a test setup with LEDs and sensors.

Explore a graphical programming environment that lets beginners drag and drop to code microcontrollers, converting visuals to text for Arduino, ESP, and Raspberry Pi, with a free version.

Learn to download and install the visual light software used to program ESP32 boards without coding, compare free and full versions, and set up the development environment.

Explore the user interface to configure microcontrollers by dragging and dropping components, changing the board type, and viewing pins to design a simple circuit with no coding.

Explore the visual user interface and its main components, from the left-right canvas and menus to code upload and autosave, with tools for routing, grid control, and Arduino integration.

learn to blink an led on the ESP32 using a GPIO pin, a resistor and a pulse generator at 1 Hz.

Upload a blink LED program to the ESP32 dev kit version one, using a pulse generator on GPIO pin 2 to blink at one hertz.

Upload the example to the ESP board; pressing the button connected to pin three turns on the LED connected to pin two, with no extra code required.

Upload the code to the ESP board in the ESP32 bootcamp, connect a button to digital pin 4 to control the LED, and test the push-button wiring with Arduino IDE.

Learn to connect an infrared obstacle avoidance sensor to an ESP32 board, adjust sensitivity and frequency with two potentiometers, and test for reliable obstacle detection.

Connect the ESP32 to ground and 3.3V (test 5V), wire the sensor output to GPIO4, and verify the power LED; learn to invert the signal and add start/stop functionality.

Master hardware and software essentials for ESP32 projects, including level shifting from 3.3V to 5V, wiring, Arduino IDE setup, and AMQP protocol basics for practical implementation.

Learn how mqtt enables publish-subscribe messaging for small sensors and devices, using topics and a broker to route commands and data for home automation and the Internet of Things.

Sign up for a free uncute-enabled plan with 100 users and 10 MB storage, verify email, and log in to add an ESP32 device (up to 10 devices).

Create a cloudmqtt account and launch a new instance, choosing a plan and data center. Add a user, set topic-based read/write ACLs, and note the server and port for connection.

Learn to interface an Arduino with ESP32 by sending ADC sensor data over software serial on pins 2 and 3, formatted for the ESP32.

Learn to set up the Arduino IDE for ESP32, connect to Wi‑Fi, configure MQTT via PubSubClient, and initialize Wi‑Fi and MQTT clients in code.

Learn to connect an ESP32 to wifi with retry loops, print the IP address, and implement an mqtt reconnect routine that generates a client id, publishes messages, and handles failures.

Read incoming serial data from an Arduino, buffer it, and publish to the serial publish channel after confirming Wi-Fi and server connectivity.

Connect the ESP32 to an Arduino using a logic level shifter in Fritzing, wiring 3.3v to the low side, 5v to the high, with ground and TX/RX serial lines.

Upload the arduino code to the board, select the correct arduino board, and verify readings in the serial monitor to confirm readiness to connect the two boards.

Update and upload ESP32 code via the M Kutty server, configure port, username, and password, test with WebSocket, and verify the device connects and shows its IP.

Confirm ESP32 connects to cloud and Kutty server, view a topic with Hello World messages, and prepare to connect Arduino to send sensor data to that topic.

outline ESP32 hardware and software requirements, including temperature and humidity sensors, optional water level and moisture sensors, leds, breadboard, wires, smartphone with uplink and blink apps, and the Arduino IDE.

Learn to monitor sensor data and remotely control high voltage devices with an ESP32 connected via blink, enabling real-time garden monitoring through a mobile app.

Design an ESP32 circuit using soil moisture, ht11 temperature and humidity sensors, and water level sensors. Learn breadboard wiring and fritzing schematics to prepare a complete circuit design.

Learn to set up and code an ESP32 project in Arduino using Wi-Fi, DHT11, and analog sensors for water and soil moisture, including library installation and pin configuration.

Read humidity and temperature with the DHT sensor, map water level and moisture readings to a 0-20 range, and transmit these values via virtual pens to the blink up library.

this lecture shows configuring ESP32 setup and loop to enable debugging at 9600 baud, set up blink‑up wifi, initialize DHT library, and schedule sensor data every three and six seconds.

Install and open the Blynk app, create a new ESP32 project, and configure gauges for temperature, humidity, water level, and soil moisture with authentication code and pins.

Download and set up the Blynk app to remotely monitor an ESP32 project, create a new project, authenticate, and configure four gauges for temperature, humidity, water level, and soil moisture.

Copy the authentication token, configure the ESP32 with your WiFi name and password, then compile, upload, and monitor sensor values as the relay is controlled.

Set up a domain and hosting to store ESP32 sensor data and view it on your website. The lesson compares free and paid hosting, creates accounts, and uploads your site.

Create and configure an ESP data database and user, then build an ESP data table with an auto-increment id, timestamp, and sensor and location fields using phpMyAdmin.

Learn to build a PHP script that receives ESP32 POST data, validates an API key, and inserts census data, location data, and value data into a database.

Write a PHP script to display readings from the ESP data table, connecting to the local database and rendering sensor data, values, and timestamps in a table.

Program an ESP32 with the Arduino IDE, configure wifi credentials and API key, and send sensor data to a server via HTTP POST using HTTPClient.

master esp32 http post requests by sending sensor readings via variables with proper headers and API key, check wifi status, and test to ensure the server receives data.

Upload code to the ESP32, verify Wi-Fi, troubleshoot issues with the wifi network name and password, and confirm sensor data posts reach the database and webpage.

Learn to read touch sensors on an ESP32 board (pins 2, 4, and 15) and display live readings on a webpage, with code you can adapt for other sensors.

Gather the hardware and software for the ESP32 bootcamp, including an ESP32 board, LEDs with resistors, jumper wires, and the Arduino IDE for programming.

learn how the observer stores processes and delivers web pages to a client, while browsers request pages via http and servers respond with content or errors.

Explore ESP32 operating modes by examining station mode, where the device connects to an existing wifi, and soft access point mode, which creates its own network.

Wire an ESP32 to a breadboard using fritzing, with LEDs and resistors, and import the ESP32 board library; create a simple LED circuit to be controlled in the coding section.

Explore how the ESP32 acts as a web server by handling HTTP GET requests from a browser, turning an LED on or off via a URL, and returning status pages.

Learn to turn an ESP32 into a wifi access point and run a web server that serves pages, while configuring local ip, gateway, and subnet settings.

Configure an ESP32 http server with routes to control LEDs via led1 and led2, set up a soft AP, and map paths for not found responses.

Learn to handle incoming requests with a server by implementing handle client, updating led states, and returning 200 or 404 responses.

Learn to generate a dynamic html page for an ESP32 web server by composing a doctype, the head elements, styling, and dynamic buttons that reflect LED states.

Practice practical ESP32 bootcamp steps to verify code, configure an access point, upload firmware, and access a web server to control LEDs via a button-based GUI.

Explore SMTP server basics, the simple mail transfer protocol, and internet standard for email transmission; learn about Gmail server details and the SB 32 Manicaland library for Arduino IDE.

Install the ESP32 mail client library for Arduino using the library manager, enabling email sending capabilities; learn to install the library and set up a new account for emails.

Create a new Gmail account to use as a sender, guiding you through account setup, recovery options, and enabling less secure access for sending emails.

Configure SMTP server settings for ESP32 by detailing Gmail, Live/Hotmail, and Office 365 SMTP, including full email as username and ports 587 or 465 with TLS or SSL.

Configure wifi credentials and SMTP settings, include the ESP32 mail client library, and send a test email via Gmail SMTP server (port 465) with a subject and plain text message.

Learn to build an ESP32 email alert project part 2 by composing a plaintext email, setting recipient data, using a send email function, and implementing a status callback before upload.

Upload and verify code on the ESP32 with Arduino IDE, monitor serial output, and configure email sending (plain text or encoded) for practical testing.

Configure an ESP32 project to send an email alert when the touch sensor on the SSP board reaches 100, including sensor data. Use a delay to prevent repeats.

Meet the Educational Engineering Team, seasoned microcontroller experts sharing real-world, step-by-step, bite-sized videos to deepen understanding and empower students and hobbyists around the world.